System Base III
INON INC. is pleased to announce official release of the System Base III relating products offering broad compatibility to support from compact housings to SLR housings on January 18th, 2019.
Main Base III
--Release date: January 18th, 2019
--JAN Code: 456212143 916 0
Holder III (*1)
--Release date: January 18th, 2019
--JAN Code: 456212143 917 7
(*1) Upon release of the Holder III, the Holder II will be discontinued and available from limited stock at our dealers.
Holder III Set
A set of one each of Main Base III and Holder III
--Release date: January 18th, 2019
--JAN Code: 456212143 918 4
■ Main Base III product features
An essential base plate securely attached on the bottom of an underwater housing with two tripod screws to add a handle. As the width between tripod screws is variable at 33-105mm/1.3-4.1inch, this base widely supports from compact housings to SLR housings enabling you to use same base tray when upgrading camera system.
Compatible products:
-INON X1 series housing
-INON X-2 series housing
-Olympus PT-EP01, PT-EP03, PT-EP05L, PT-EP06L, PT-EP08, PT-EP10, PT-EP11, PT-EP12, PT-EP13, PT-EP14, PT-053, PT-054, PT-055, PT-056, PT-058
-SONY MPK-URX100A, MPK-HSR1
-Nikon WP-N1, WP-N2, WP-N3
Both ends can have optional Holder III (*2).
(*2)
The Holder II and D Holder is not compatible with the Main Base III.
The Main Base III is equipped with four screw holes each on both ends enabling to attach optional Holder III at three different angles (*3)
(*3) When installing the Holder III at a right angle (above right image), the Holder III may interrupt opening/closure of the combined housing. If this happens, please remove the Holder III to open/close the combined housing.
It is easy to install on the INON UW 3-Way Panhead via its packaged Panhead Adapter Base to use on an INON underwater tripod system.
Replacing pre-installed tripod screws with optional 12-24 Tripod Screw Set for Grip Base M1 enables to attach the Main Base III on an underwater housing equipped with 12-24UNC screws on its bottom.
■ Holder III product features
Dedicated handle for the Main Base III to attach either end of the Main Base III. Elongate slots equipped on the bottom allows to have ample range to adjust handle position side ways to suits to a compact housing as well as large DSLR housing.
The top end of the Holder III can be configured with variety of INON adapters and cold shoe accessories.
Example of combination (from left):
-Direct Base III
-Multi Direct Base IIa
-Multi Direct Base II Long
-Multi Direct Base II WB
-Z Adapter II
Example of combination (from left):
-Direct Base YS RT
-Shoe Base Adapter D4 + Shoe Base 1/4-20UNC
-Shoe Base Adapter D4 + Shoe Base M6
-Shoe Base Adapter D4 + Shoe Base BALL
-Shoe Base Adapter D4 + Shoe Base II
● Compatible product
-INON Main Base III (*4)
(*4) Compatible with Main Base III only and not compatible with Main Base II, D Base SPS; a base tray for Grip Base D4 or D Base M1; a base tray for Grip Base M1.
January 17, 2019
INON INC.
*Press release information is as of January 17, 2019 and subject to change without prior notice.
Main Base III
--Release date: January 18th, 2019
--JAN Code: 456212143 916 0
Holder III (*1)
--Release date: January 18th, 2019
--JAN Code: 456212143 917 7
(*1) Upon release of the Holder III, the Holder II will be discontinued and available from limited stock at our dealers.
Holder III Set
A set of one each of Main Base III and Holder III
--Release date: January 18th, 2019
--JAN Code: 456212143 918 4
■ Main Base III product features
An essential base plate securely attached on the bottom of an underwater housing with two tripod screws to add a handle. As the width between tripod screws is variable at 33-105mm/1.3-4.1inch, this base widely supports from compact housings to SLR housings enabling you to use same base tray when upgrading camera system.
Compatible products:
-INON X1 series housing
-INON X-2 series housing
-Olympus PT-EP01, PT-EP03, PT-EP05L, PT-EP06L, PT-EP08, PT-EP10, PT-EP11, PT-EP12, PT-EP13, PT-EP14, PT-053, PT-054, PT-055, PT-056, PT-058
-SONY MPK-URX100A, MPK-HSR1
-Nikon WP-N1, WP-N2, WP-N3
Both ends can have optional Holder III (*2).
(*2)
The Holder II and D Holder is not compatible with the Main Base III.
The Main Base III is equipped with four screw holes each on both ends enabling to attach optional Holder III at three different angles (*3)
(*3) When installing the Holder III at a right angle (above right image), the Holder III may interrupt opening/closure of the combined housing. If this happens, please remove the Holder III to open/close the combined housing.
It is easy to install on the INON UW 3-Way Panhead via its packaged Panhead Adapter Base to use on an INON underwater tripod system.
Replacing pre-installed tripod screws with optional 12-24 Tripod Screw Set for Grip Base M1 enables to attach the Main Base III on an underwater housing equipped with 12-24UNC screws on its bottom.
■ Holder III product features
Dedicated handle for the Main Base III to attach either end of the Main Base III. Elongate slots equipped on the bottom allows to have ample range to adjust handle position side ways to suits to a compact housing as well as large DSLR housing.
Example of combination (from left):
-Direct Base III
-Multi Direct Base IIa
-Multi Direct Base II Long
-Multi Direct Base II WB
-Z Adapter II
Example of combination (from left):
-Direct Base YS RT
-Shoe Base Adapter D4 + Shoe Base 1/4-20UNC
-Shoe Base Adapter D4 + Shoe Base M6
-Shoe Base Adapter D4 + Shoe Base BALL
-Shoe Base Adapter D4 + Shoe Base II
● Compatible product
-INON Main Base III (*4)
(*4) Compatible with Main Base III only and not compatible with Main Base II, D Base SPS; a base tray for Grip Base D4 or D Base M1; a base tray for Grip Base M1.
January 17, 2019
INON INC.
*Press release information is as of January 17, 2019 and subject to change without prior notice.
